Powder Coating in Metal Fabrication

Powder coating metal products in Vietnam

Short answer: Powder coating is a dry finish: a resin and pigment powder is sprayed electrostatically onto pretreated metal and cured in an oven. Polyester (TGIC or HAA cured) and polyurethane powders are used outdoors, epoxy gives the highest chemical and corrosion resistance but loses color in sunlight, and epoxy-polyester hybrids are for indoor parts. Typical decorative films are about 2-3 mils (roughly 50-75 µm), checked with magnetic or eddy-current gauges as described in ASTM D7091.

Last updated: November 2, 2026.

Introduction

In the world of metal fabrication, powder coating is one of the most popular and durable finishing solutions. Known for its excellent resistance to corrosion, impact, and weathering, powder coating is widely used in manufacturing outdoor products, automotive parts, furniture frames, and more.

For buyers sourcing from Asia, Vietnam is an established option for fabricated and powder-coated metal products. This article explains the powder coating process, how the main powder types differ, what film thickness and pretreatment to specify, and what to check when sourcing from Vietnam.

What is Powder Coating?

Powder coating is a dry finishing process where a fine powder (typically polyester, epoxy, epoxy-polyester hybrid, polyurethane or acrylic) is electrostatically sprayed onto a metal surface and then cured under heat. It forms a tough, uniform coating without the solvents used in most liquid paints.

Key steps in powder coating:

  • Pre-treatment: Cleaning and degreasing to remove contaminants, usually followed by a conversion coating such as iron or zinc phosphate.

  • Spraying: Electrostatic application of powder onto the metal.

  • Curing: Heating the coated part to fuse the powder into a smooth layer.

Powder coating process: cleaning, spraying, curing
Powder coating process: cleaning, spraying, curing

Benefits of Powder Coating in Metal Fabrication

  • Superior Durability: Powder coating provides a highly resistant finish that protects against scratches, chipping, fading and rust. UV resistance depends on the resin: polyester and polyurethane powders are used outdoors, while epoxy powders lose gloss and color in direct sunlight.

  •  Eco-Friendly Process: Unlike solvent-borne liquid paint, powder coating emits virtually no VOCs (volatile organic compounds), and the U.S. EPA describes powder coatings as generally the lowest polluting of all coatings.

  •  Aesthetic Flexibility: Available in a wide range of colors, textures (matte, gloss, textured), and thickness levels to meet design specifications.

  • Cost-Effective for Large Volumes: Minimal waste, fast application, and long-lasting results reduce long-term maintenance and repainting costs.

Powder types compared

The resin decides where a powder can be used (sources: ChemQuest, Powder Coating Institute).

Powder type Indoor / outdoor UV resistance Chemical and corrosion resistance Typical uses
Epoxy Indoor, or parts out of direct sun Poor; limited gloss and color retention Very high Pipe, rebar, primers
Epoxy-polyester hybrid Indoor Sufficient for indoor use only High Appliances, office furniture
Polyester (TGIC or HAA cured) Outdoor Good; about 1-3 years UV durability for standard grades, 3-7 years for super-durable Moderate; epoxy primer for harsh sites Garden equipment, outdoor furniture
Polyurethane (polyester cured with blocked isocyanate) Indoor and outdoor Good Very good Anti-graffiti, harsh cleaning

For architectural aluminum, FGIA’s AAMA 2603, 2604 and 2605 set good, better and best tiers; per Products Finishing, they require one, five and ten years of outdoor weathering respectively. For steel parts, state the powder chemistry and film thickness in your drawing instead.

Film thickness and pretreatment

Pretreatment improves adhesion and corrosion resistance. A typical sequence for steel:

  1. Clean and degrease.
  2. Blast rusty or scaled surfaces.
  3. Apply a conversion coating: iron phosphate (steel and aluminum) or zinc phosphate (steel and galvanized steel).
  4. Rinse and dry.
  5. Spray the powder electrostatically and oven-cure it.
Application Typical dry film thickness
Indoor decorative parts Minimum 50 µm (2.0 mils); 60-75 µm (2.4-3.0 mils) preferred
Demanding decorative environments 75-100 µm (3.0-4.0 mils)
Functional coatings (rebar, pipe) 200 to over 400 µm (8-16 mils)

Figures are from ChemQuest. Thickness is measured with magnetic gauges on steel and eddy-current gauges on nonferrous metals, following ASTM D7091; specify how many readings are taken per part.

Powder coating benefits in metal fabrication at HD Mechanical Vietnam
Enhance durability and quality of metal products with professional powder coating.

 

Why Choose Vietnam for Powder Coated Metal Products?

Finishing capability varies from factory to factory, so check these points when qualifying a Vietnamese supplier.

What to check:

  • Coating line: Booth type, pretreatment stages and how oven temperature is controlled.

  • Surface preparation: How parts are cleaned, blasted or phosphated before coating, and how film thickness is checked.

  • Total landed cost: Compare unit price together with freight, duties and packaging; see our landed cost guide.

  • Material compliance: Ask for the powder manufacturer’s technical and safety data sheets, and any RoHS or REACH declarations your market requires.

Common Powder-Coated Products for Export

  • Mailboxes and outdoor enclosures

  • Furniture frames (benches, tables, chairs)

  • Industrial control panels

  • Automotive accessories and brackets

  • Decorative metal screens

HD Mechanical Vietnam ships products like these to export brands in the US, Europe and Australia; the finish specification is set by the buyer and the end use. See our mailboxes and electrical cabinets for typical powder-coated parts.

Custom metal products for export by HDMP
Powder-Coated products for export by HD Mechanical Vietnam

Powder Coating at HD Mechanical Vietnam 

At HD Mechanical Vietnam , we provide OEM metal fabrication with in-house powder coating for export products.

What we offer:

  • Electrostatic powder coating and oven curing, with in-house QC

  • Standard and custom RAL colors in matte, gloss or textured finishes

  • Sandblasting and surface preparation before coating

  • Other finishes on request, including hot-dip galvanizing and electroplating

  • Export-ready packaging and documentation

Request a sample or quote from our sales team.

Conclusion

Powder coating is a durable, low-VOC finish for most steel and aluminum products, provided the resin, pretreatment and film thickness match the end use. Put those three items in your specification. For outdoor material choices, see galvanized vs. stainless steel.

Frequently asked questions

What powder coating is best for outdoor metal products?

Polyester (TGIC or HAA cured) is the usual choice because it holds color and gloss in sunlight; super-durable polyester grades last longer. Epoxy and epoxy-polyester hybrid powders are intended for indoor use.

How thick should powder coating be?

Typical decorative films are about 2-3 mils (roughly 50-75 µm), with 75-100 µm for demanding environments. The powder’s technical data sheet gives the recommended range.

How is powder coating thickness measured?

With magnetic gauges on steel and eddy-current gauges on aluminum, as described in ASTM D7091. Take several readings per part, because thickness varies across a surface.

What pretreatment is needed before powder coating steel?

Cleaning and degreasing, blasting if the steel is rusty or scaled, then an iron or zinc phosphate conversion coating for better adhesion and corrosion resistance.

Sources

 Want to see the difference HD Mechanical Vietnam’s powder coating can make for your next project?
Contact us today to discuss your specifications.

Leave a Reply

Your email address will not be published. Required fields are marked *