Short answer: pick the lid for the main problem at the site: a dome or hooded top for rain, snow and wind, a rain bonnet for weather protection with access from almost every side, a flat top for touch-free use, and a side door when crews need to empty the bin quickly. Choose a molded plastic liner where drinks or salt air would corrode steel, and a zinc-coated steel liner where cigarettes are thrown in. Size bags from the liner itself: width is half the circumference, and length is the depth plus half the diameter plus 3 to 4 in of overhang.
Last updated: November 18, 2026.
This guide is for park departments, streetscape contractors and site-furnishing distributors who buy or resell outdoor receptacles. For capacity, body style and mounting, see our commercial trash receptacle buying guide.
Lid types at a glance
The lid descriptions below come from the trash receptacle guides of The Park Catalog and Wabash Valley.
| Lid | How it works | What it solves | Trade-off |
|---|---|---|---|
| Flat top (pitch-in) | Open slot in a flat lid | Touch-free use, fewer moving parts | Less weather protection than a dome |
| Dome top | Domed lid with an opening or a lifting handle | Resists rain, snow and wind; a handle also keeps out smaller animals | Visitors lift the lid by its handle |
| Hooded top | Hood over an opening, no push door | Some rain protection, contactless | Less cover than a dome |
| Rain bonnet | Raised cap over the open top | Keeps contents dry with nearly 360 degree access | Less enclosed than a dome |
| Bullet or push door | Round top with a door that swings closed | Funnels items in; door closes after use | A moving part to maintain |
| Ashtray or recycler top | Ash urn on the lid, or several openings by material | Cigarette litter, sorted recycling | Separate compartments to service |
Emptying is a separate choice. A side access door that slides, pulls or swings open lets staff tilt the liner out through the side, which The Park Catalog notes is easier for crews but adds moving parts to maintain. Top-loading bins are emptied by lifting the lid and pulling the liner out vertically.
Matching the lid to the site problem
- Rain and snow: an uncovered open top collects water and adds weight to every bag. A dome, hood or rain bonnet keeps most weather out.
- Wind: a dome or hood limits litter blowing out; anchor the body as well, since a light bin can tip in gusts.
- Animals: a dome with a handle deters small animals. In bear country, buy a tested design. The Interagency Grizzly Bear Committee testing protocol exposes products such as garbage carts to captive grizzly bears for up to 60 minutes of bear contact time, while metal dumpsters, garbage can enclosures and bag holders are generally assessed by a technical evaluation of construction and latches.
- Smoking: an ashtray top reduces butt litter, and the liner under it should be steel (see below).
- Emptying: a side door suits frequent service routes; a lift-off or hinged lid suits lower budgets with fewer parts.
Liners: molded plastic or zinc-coated steel
An inner liner keeps the body clean and lets full bags come out in one lift. UK street furniture maker Glasdon sets out the trade-offs:
| Factor | Molded plastic liner | Zinc-coated steel liner |
|---|---|---|
| Weight | Significantly lighter | Up to 75 percent heavier |
| Noise when emptying | Noticeably quieter | Louder |
| Acidic drinks | Recommended where possible | Acids eat away at many metals over time |
| Coastal sites | Recommended, as salt water speeds rusting | Zinc coating extends life but rust risk remains |
| Cigarettes and fire | Steel preferred | Strongly recommended for bins with smoking control; required with Glasdon’s fire safety device |
Glasdon also recommends using a sack inside either liner to speed emptying. Specify the liner’s inner diameter or width and its depth on your drawing, because those numbers, not the nominal gallon rating, decide which bag fits.
How to size bags to the liner
Liner bags are listed as width by length, for example 35 x 50 in, where width is the flat opening. AAA Polymer and Interplas describe the same method:
- Width: measure the circumference and divide by 2. For a round liner, circumference is the diameter times 3.14; for a square or rectangular liner, add the four sides.
- Length: add the liner depth, the lay-flat allowance for the base (half the diameter for a round liner, half the diagonal of the base for a square one) and 3 to 4 in of overhang.
- Material: AAA Polymer suggests LLDPE for heavy, irregular or sharp waste such as food and yard debris, and HDPE for lighter, non-sharp waste such as paper.
Worked example: a round inner liner 20 in in diameter and 28 in deep has a circumference of 20 x 3.14 = 62.8 in, so the bag width is about 31.4 in. Length is 28 + 10 + 4 = 42 in. Choose a stock bag at or just above about 32 x 42 in.
Published charts give a starting point for common plastic containers. Tenaquip’s garbage bag size chart lists these optimal bags:
| Container capacity | Approx. liters | Optimal bag (width x length) |
|---|---|---|
| 20 to 23 US gal | 76 to 87 L | 30 x 38 in |
| 32 to 33 US gal | 121 to 125 L | 35 x 48 in to 35 x 50 in |
| 55 US gal | 208 L | 42 x 48 in |
Liters use the NIST factor of 3.79 liters per US gallon. Tenaquip rates bags above 1.3 mil as heavy duty for industrial or outdoor waste. Two bins with the same gallon rating can need different bags, so always check the formula against your liner.
What to put in the specification
- Lid type and opening size, and whether the lid is hinged, lift-off, locked or tethered.
- Emptying method: top lift or side door, and the lock or latch type.
- Liner material, inner dimensions, drain holes if wanted, and handles.
- Target bag size, so the liner and your bag stock match.
- Body finish and color, and surface mounting if wind or theft is a concern.
Receptacles from HD Mechanical Vietnam
HD Mechanical Vietnam builds the metal slatted trash receptacle and the metal mesh receptacle in carbon, galvanized or stainless steel, powder coated or hot-dip galvanized, in black, gray, green or custom RAL colors, freestanding or surface mounted. For coastal or very wet sites, the mesh product page recommends stainless or hot-dip galvanized steel with a powder coat. Size, shape and branding are made to your drawing or sample, so show the lid style, emptying method and liner dimensions on the drawing for the quote. See the full trash receptacle range.
Frequently asked questions
Which trash can lid is best for rain?
A dome or hooded top keeps out most rain and snow. A rain bonnet also keeps contents dry while leaving access from nearly every side.
Should an outdoor trash receptacle have a plastic or metal liner?
Plastic is lighter, quieter and better with acidic drinks and salt air. Choose zinc-coated steel where people put cigarettes in the bin.
How do I work out the bag size for a trash receptacle?
Bag width is half the liner’s circumference. Bag length is the liner depth plus half its diameter plus 3 to 4 inches of overhang.
What size bag fits a 32 gallon trash can?
Tenaquip’s chart lists 35 x 48 in to 35 x 50 in for 32 to 33 gallon containers. Check the formula against your actual liner, since shapes differ.
How many liters is a 32 gallon trash receptacle?
About 121 liters, using the NIST factor of 3.79 liters per US gallon.
Sources
- Buyer’s Guide for Trash Receptacles – The Park Catalog
- Outdoor Trash Receptacle FAQ – Wabash Valley
- Bear-Resistant Products Testing Program Testing Protocol – Interagency Grizzly Bear Committee
- Liner Choice – Glasdon
- 3 Quick Steps to Can Liner Right Sizing – AAA Polymer
- How to Measure for a Can Liner – Interplas
- Garbage Bag Size Chart – Tenaquip
- Approximate Conversions from U.S. Customary Measures to Metric – NIST
Request a trash receptacle quote
Send your drawing or reference photo with the lid style, liner type and dimensions, finish, quantity and destination port through our contact page or WhatsApp +84 98 878 53 93.

