Short answer: in the US, the MUTCD requires post-mounted sign supports within the clear zone to be crashworthy, which for small signs usually means breakaway or yielding U-channel or perforated square steel tube posts. Crashworthiness belongs to a tested system, not to a post on its own: the post, base, anchor, splice and installation must match the configuration described in the crash test or FHWA eligibility letter. A buyer should therefore specify posts that are built to the approved system’s material, weight and geometry.
Last updated: November 20, 2026.
This guide is for traffic sign distributors, highway contractors and municipal suppliers. For a comparison of the two post types, see U-channel vs square sign posts.
Why roadside sign supports must be crashworthy
The MUTCD 11th Edition, Chapter 2A states in Section 2A.16 that post-mounted sign and object marker supports shall be crashworthy if within the clear zone, and that lateral offset does not replace that requirement. Section 2A.13 says signs should be outside the clear zone unless placed on a crashworthy support. Part 1, Section 1C.02 defines the terms:
- Crashworthy: the ability of roadside hardware to minimize risks to occupants by letting an impacting vehicle be slowed before stopping, redirected, or continue without significant resistance.
- Clear zone: the total roadside border area, starting at the edge of the traveled way, available for an errant driver to stop or regain control.
FHWA’s guide Maintenance of Signs and Sign Supports notes that barriers are rarely used to shield small signs on local roads, so the post itself must break away or yield.
Crash test criteria: NCHRP 350 and MASH
Older sign supports were evaluated under NCHRP Report 350, current hardware under the AASHTO Manual for Assessing Safety Hardware (MASH). An FHWA memorandum of May 8, 2018 explains that AASHTO and FHWA signed a joint agreement defining the actions needed for full implementation of MASH 2016 by December 31, 2019, with sunset dates for different hardware types. A 2015 FHWA open letter added that changes to any existing NCHRP 350 device require testing to MASH criteria. Check which criteria the buying agency applies.

Breakaway mechanisms for U-channel and square posts
The FHWA maintenance guide describes how each post type achieves breakaway or yielding behavior:
| Post type | Typical use | Breakaway or yielding method described by FHWA |
|---|---|---|
| U-channel, light | Small regulatory, warning and street name signs | A re-rolled rail steel post of 3 lb/ft or less bends, breaks or pulls out on its own |
| U-channel, heavier | Larger or higher-mounted small signs | A commercial splice at ground level, or a stub post set in a concrete base and bolted to the sign post |
| Perforated square steel tube | Small signs where posts are replaced often | A sleeve assembly at the base or a slip coupling near the base; described as breakaway at 2 1/4 in or smaller |
| Wood post | Where wood is economical | Posts larger than 4 × 4 in drilled perpendicular to traffic |
The U-channel figure refers to re-rolled rail steel. A post of the same weight in a different steel or profile may behave differently in a crash, which is why the tested material matters.
What an FHWA eligibility letter tells you
FHWA issues Federal-aid reimbursement eligibility letters for roadside hardware as a service to State DOTs. Its eligibility process page states that letters are not required for a State DOT to install a device or to receive Federal-aid reimbursement, but they identify systems FHWA has reviewed. Two example letters show what they contain:
| Letter | System | Key conditions |
|---|---|---|
| SS-131A (2012) | Breakaway coupler for 2 1/4 in and 2 1/2 in perforated square steel tube posts with a 3 in square anchor or surface base, NCHRP 350 Test Level 3 | Not an endorsement; manufacturer certifies the hardware has the same chemistry, mechanical properties and geometry as submitted; may be installed under the range of conditions tested |
| SS-147 (2007) | 2 1/2 lb/ft U-channel bolted to a 1 3/4 in square tube riser in a concrete-set base, NCHRP 350 Test Level 3 | Accepted when installed as shown in the drawing; limited to crashworthiness; hardware must have essentially the same chemistry, mechanical properties and geometry |
A letter covers a defined post, base, connection and installation. Posts from a new source are only covered if they match it, and a manufacturer that changes hardware covered by a letter must notify FHWA under the 2015 process update.
Installation depth and anchor considerations
- U-channel: FHWA’s guide says to drive the post into the ground rather than encase it in concrete; a broken post is easier to remove if set no deeper than 3.5 ft.
- Square tube: drive the post or anchor with no concrete around the post, and do not set it more than 3 ft deep.
- Tested details: SS-147, for example, specifies two 5/16 in Grade 5 bolts 4 in apart, a riser inserted at least 4 in into its base and a footing at least 8 in deep.
- Mounting height: MUTCD Section 2A.15 requires at least 7 ft from the ground to the bottom of signs over 50 sq ft on multiple breakaway posts, and at least 7 ft above a sidewalk.
- Post spacing: FHWA warns that posts too close together can affect crashworthiness; follow the tested spacing.

What to specify when sourcing sign posts
- The crashworthy system you are matching, with its eligibility letter number or agency approval
- Post profile and weight (lb/ft) for U-channel, or size and gauge for square tube
- Steel grade and mechanical properties to match the tested post, with mill certificates
- Hole diameter and spacing, length and end condition
- Anchor, sleeve, splice or base hardware, and who supplies it
- Finish and color, plus marking and packaging
Where HD Mechanical Vietnam fits
HD Mechanical Vietnam manufactures sign posts to the buyer’s specification. HD posts are not crash tested and hold no FHWA eligibility letter, so their crashworthiness depends on being built to an approved system’s specification and installed as that system requires. The steel U-channel page lists 1.12 and 2.00 lb/ft posts in 3 to 12 ft lengths with 3/8 in holes at 1 in centers, powder coated or hot-dip galvanized. The square sign post page lists 12, 14 and 16 gauge walls in 6, 8 and 10 ft heights, compatible with anchor and telescopic base systems. Length, weight, hole spacing and finish can be customized to your approved drawing; confirm the steel grade and mechanical properties with the factory before ordering.

Frequently asked questions
Do sign posts have to be breakaway?
In the US, post-mounted sign supports within the clear zone must be crashworthy under MUTCD Section 2A.16. Overhead supports in the clear zone must instead be shielded by a barrier or crash cushion.
Is a U-channel post crashworthy on its own?
Only as part of a tested configuration. FHWA describes re-rolled rail steel U-channel of 3 lb/ft or less as breakaway on its own, while heavier posts need a splice or stub base.
What is an FHWA eligibility letter for sign supports?
It states that a defined hardware system is eligible for Federal-aid reimbursement based on crash testing or analysis. It is not an endorsement and covers only hardware matching the reviewed system.
How deep should a square sign post be installed?
FHWA’s maintenance guide says square tube posts should be driven with no concrete around the post and set no more than 3 ft deep. Follow the tested system’s anchor and embedment details where they differ.
Are HD Mechanical sign posts crash tested?
No. HD Mechanical builds U-channel and square posts to the buyer’s specification and holds no crash test or FHWA eligibility letter, so specify posts that match an approved system.
Sources
- Manual on Uniform Traffic Control Devices, 11th Edition, Chapter 2A, FHWA
- Manual on Uniform Traffic Control Devices, 11th Edition, Part 1, FHWA
- Maintenance of Signs and Sign Supports, IV. Sign Supports, FHWA
- Clarifications on Implementing the AASHTO Manual for Assessing Safety Hardware, 2016 Edition (May 8, 2018), FHWA
- Open letter: updates to the Federal-aid reimbursement eligibility process (November 12, 2015), FHWA
- Federal-aid Reimbursement Eligibility Process, FHWA
- Eligibility letter SS-131A, FHWA
- Eligibility letter SS-147, FHWA
Request a sign post quote
Send the approved system drawing, post type, weight or gauge, length, finish and quantities for a quote. See the steel U-channel and square sign post pages, then contact us through the contact page or WhatsApp +84 98 878 53 93.

