Metal Bed Frame Sizes by Market: US, UK, EU and Australia

Metal bed frame sizes by market

Short answer: the same size name means a different mattress in each market. A US queen is 60 × 80 in (152 × 203 cm), a UK king is 150 × 200 cm, the classic EU couples’ size is 160 × 200 cm, and an Australian queen is 153 × 203 cm. Build the frame around the mattress dimensions of the target market, add only 1–2 cm of play inside the rails, and check slat gaps and center support against the mattress brands your customers use.

Last updated: November 20, 2026.

This guide is for furniture brands, hotel FF&E buyers and importers who source one metal bed frame design for several markets. For the product itself, see our metal bed frame page.

Mattress sizes by market

US sizes are from the Sleep Foundation, UK sizes from Bed Advice UK, run by the National Bed Federation, EU sizes from German retailer Sleep Hero and Australian sizes from national retailer Forty Winks. Values in the second unit are converted.

Market Size name Inches (W × L) cm (W × L)
US Twin 38 × 75 96.5 × 190.5
US Full 54 × 75 137.2 × 190.5
US Queen 60 × 80 152.4 × 203.2
US King 76 × 80 193.0 × 203.2
US California king 72 × 84 182.9 × 213.4
UK Single 36 × 75 (3 ft × 6 ft 3 in) 90 × 190
UK Small double 48 × 75 (4 ft × 6 ft 3 in) 120 × 190
UK Double 54 × 75 (4 ft 6 in × 6 ft 3 in) 135 × 190
UK King 60 × 78 (5 ft × 6 ft 6 in) 150 × 200
UK Super king 72 × 78 (6 ft × 6 ft 6 in) 180 × 200
EU 90 × 200 (single) 35.4 × 78.7 90 × 200
EU 140 × 200 55.1 × 78.7 140 × 200
EU 160 × 200 (classic couples’ size) 63.0 × 78.7 160 × 200
EU 180 × 200 70.9 × 78.7 180 × 200
Australia Single 36.2 × 74.0 92 × 188
Australia King single 42.1 × 79.9 107 × 203
Australia Double 54.3 × 74.0 138 × 188
Australia Queen 60.2 × 79.9 153 × 203
Australia King 72.0 × 79.9 183 × 203

For a multi-market range:

  • Names do not transfer. A UK king is close to a US queen, and a US king is 10 cm wider than an Australian king.
  • EU sizes are named by dimensions. Sleep Hero lists widths from 80 to 200 cm on a standard 200 cm length.
  • Sizes vary between retailers in one market. IKEA Australia lists its standard king as 180 × 200 cm and its queen as 152 × 202 cm, both different from the figures above. Confirm the mattress your buyer actually sells.

Frame inner dimensions and allowance

Harvey Norman UK tells customers to measure width between the inside faces of the rails and length from inside the headboard to inside the footboard, and notes that UK frames often have 1–2 cm of slack. Swiss mattress maker Ora Sleep gives the same range: a maximum of one to two centimeters of play, because more lets the mattress slide. Specify the inner dimension as mattress size plus play, say whether play is per side or total, and set a tolerance.

Steel frame fabrication stations
Steel frame fabrication stations.

Slat spacing and center support

Slat gaps and leg counts are usually set by mattress warranties and retailer guidance rather than one universal rule:

Source Slat gap Other requirements
Tempur Sealy (Sealy and Stearns & Foster mattresses) No more than 4 in (about 10 cm) Slats at least 3 in wide; frame must include a center support; at least 4 legs for twin and full, 5–6 legs for queen, king and California king
Bensons for Beds (UK) 7 cm maximum Rule of thumb for slatted bases
Ora Sleep (Switzerland) 3–4 cm maximum Center support for beds 160 cm wide or more

A frame that meets the tightest figure your customers face can use one slat layout everywhere. For Europe and the UK, buyers may also cite EN 1725, published in 2023 as Furniture – Beds – Requirements for safety, strength and durability and listed by FIRA as BS EN 1725:2023. Confirm the edition and clauses with your buyer or test lab before sampling.

Flat-pack and export packaging

Long side rails set the carton length, which decides freight cost and which carriers accept the parcel. UPS accepts packages up to 150 lb, 108 in long and 165 in in length plus girth; larger combinations may need freight service. A split rail with a bolted joint can keep a king or California king frame inside parcel limits. Our post on packaging for export-ready metal products covers protection, labeling and carton design.

Finishes

Powder coat is the usual finish for indoor frames; state the RAL code, gloss level and any adhesion or salt spray report you need. Our guide to powder coating in metal fabrication explains pretreatment and coating options.

Fabrication workbench in the factory
Fabrication workbench in the factory.

What to specify

  1. Target market and the exact mattress size, in cm or inches, for every SKU.
  2. Inner dimension, play and tolerance, measured between the inside faces of the rails.
  3. Slat width, maximum gap and slat material, matched to the mattress warranties you need to meet.
  4. Number and position of center legs for each size, and floor protection under each foot.
  5. Headboard and footboard mounting holes, if the frame must accept third-party headboards.
  6. Finish, color code and test reports.
  7. Carton count, maximum carton dimensions and weight, hardware packing and labeling.
  8. Any standard, such as EN 1725, with edition and test lab.

HD Mechanical metal bed frames

HD Mechanical Vietnam produces metal bed frames in powder-coated or galvanized steel, in twin, full, queen and king sizes and in custom sizes, with width, height and leg spacing adjustable to your drawing. Options include platform, headboard-compatible and daybed styles, reinforced steel slats, a center support leg and pre-drilled headboard holes. Frames ship knock-down with foam, corner guards, labeled hardware bags and cartons sized to carrier limits, printed with your artwork and barcodes. Colors are black, white, grey or custom RAL. Each project runs from CAD drawing and quotation to an approved pre-production sample, then production with inspection at each stage. See also metal furniture solutions.

Steel frames and parts on the fabrication floor
Steel frames and parts on the fabrication floor.

Frequently asked questions

Is a UK king the same as a US king?

No. A UK king is 150 × 200 cm, while a US king is 76 × 80 in (193 × 203 cm), so the UK king is closer to a US queen.

What are the standard EU bed sizes?

EU mattresses are named by dimensions, usually on a 200 cm length. Common sizes are 90 × 200, 140 × 200, 160 × 200 (the classic couples’ size) and 180 × 200 cm.

How much bigger should a bed frame be than the mattress?

Only slightly. Ora Sleep recommends a maximum of one to two centimeters of play, and Harvey Norman UK notes that UK frames often have 1–2 cm of slack.

How far apart should bed frame slats be?

It depends on the mattress. Tempur Sealy requires gaps of no more than 4 in for Sealy mattresses, Bensons for Beds suggests 7 cm maximum and Ora Sleep recommends 3–4 cm.

Does a queen or king metal bed frame need center legs?

Yes, in most cases. Tempur Sealy requires a center support and 5–6 legs for queen and king sizes, and Ora Sleep recommends center support from 160 cm wide.

Sources

Request a metal bed frame quote

Send your target markets, mattress sizes and drawings for our metal bed frame. Contact us through the contact page or WhatsApp +84 98 878 53 93.

Leave a Reply

Your email address will not be published. Required fields are marked *